Contents

Member


Site Design and Hosting By:
Moore-wds.com

CeRam-Kote Application Division awarded frac tank coating contract at facility in Big Spring, Texas.

Click here for sell sheet / performance profile

New Oil & Gas Video

Products:
CeRam-Kote 54® - Recommended for critical service. Ceramic particle loaded epoxy resin system for use in the toughest environments to protect expensive equipment. Excellent corrosion barrier, high adhesion, low permeability, sliding abrasion resistance, high surface lubricity, flexible, and is a fast, one-coat, two pass spray application. No primer needed. CeRam-Kote 54® ATM has ABS Type Approval as per certificate #99-HS27360-X and ABS Certificate of Design Assessment #03-115391002-PDA. CeRam-Kote 54® has Germanischer Lloyd Type Approval for seawater ballast water tanks, voids and cofferdams in Seagoing ships, Structural parts of offshore wind mills exposed to splash zone and seawater (approval #GL-CORR 1026 HH) and for Structural components of offshore wind mills, exposed to sea atmosphere (approval #GL-CORR 1027 HH). CeRam-Kote 54® DNV (Det Norske Veritas) Type Approval Certificate #K-1966 for protection of structural steel in ships ballast tanks, submerged in seawater, and in splash zone.

CeRam-Kote 2000 - Chemical resistant novalac ceramic/epoxy coating recommended for critical service. A derivative of CeRam-Kote 54®, CeRam-Kote 2000 is highly crosslinked to perform well in a variety of aggressive immersion service environments. Fast, one-coat, two pass spray application. No primer needed.

CeRam-Kote Marine - is a thin-film, spray-applied and air-cured ceramic epoxy coating system recommended for atmospheric corrosion/light abrasion resistance as well as non-chemical immersion service in a marine environment. Not designed for critical service, areas of high abrasion/heavy impact and/or chemical resistance. CeRam-Kote Marine is available in a variety of colors. Fast, one-coat, two pass application. No primer needed. Must be topcoated when aesthetics are an issue.

CeRam-Kote 60 / CeRam-Thane 300 System - Two-coat system is specifically engineered to provide atmospheric corrosion control where UV protection and cosmetics are important. The system is not recommended for chemical immersion service. The CeRam-Kote 60 / CeRam-Thane 200 system can be matched to most colors. No primer is necessary when using the CeRam-Kote 60 / CeRam-Thane 200 system. CeRam-Kote 60 is applied directly to the properly prepared substrate in one pass followed by one pass of CeRam-Thane 200. Typically, this application can be completed in the same working day.

CeRam-Kote 99 - Recommended for atmosphneric corrosion/light abrasion resistance as well as non-chemical immersion service. Ceramic particle loaded expoxy resin system engineered for non-critical service areas. Not designed for critical service areas of high abrasion, heavy impact and/or chemical service. Fast, one-coat, two pass spray application. No primer needed.

CeRam-Kote 99M - is a thin-film, spray applied and air-cured ceramic epoxy coating system recommended for use where water spotting is a problem. Not designed for critical service, areas of high abrasion/heavy impact and/or chemical resistance. CeRam-Kote 99M is available in a variety of colors. Fast, one coat, two pass application. No primer needed.

CeRam-Kote 99P - is a thin-film, spray applied and air-cured epoxy coating system recommended for use as a protective coating for recreational and industrial pools. CeRam-Kote 99P is available in a variety of colors. Fast, one coat, two pass application. No primer needed.

CeRam-Grout GC - Advanced ceramic/epoxy grouting material designed to handle the toughest corrosion pitting problems in steel and the most difficult cracking and spalling problems in concrete. Non-shrinking high build material resists thermal and mechanical shock. One-pass application.

CeRam-Kote SPG - Ceramic/epoxy SPRAYABLE grout designed to be a high-build corrosion barrier. As a zero VOC, two-component, 100% solids-by-volume coating, CeRam-Kote SPG provides a non-shrinking surface after application. Direct to substrate, one-coat system is a tough, durable barrier. Specialized plural component equipment is required for application. May also be brushed or rolled. CeRam-Kote SPG has Germanischer Lloyd Type Approval for ballast tanks.

CeRam-Kote SPG 22 - Advanced 100% solids ceramic/epoxy material designed to be trowel- or squeegee-applied on floors. Ideal for secondary containment applications. Non-shrinking high build material resists thermal and mechanical shock. One-coat application. Available in grey or off-white. DEP Approval as a coating for concrete secondary containment in the state of Florida.

CeRam-Floor Primer - is an epoxy resin designed to penetrate and provide a seal coat to unsealed concrete. The resin system has zero VOCs and serves as a primer for CeRam-Floor - Self Leveling Ceramic Slurry, or topcoats: CeRam-Floor TC-1 or CeRam-Thane 300.

CeRam-Floor - SELF-LEVELING CERAMIC SLURRY is a high build (30-60 mils / 750-1500 microns) protective resurfacing system which utilizes 100% solids binder resins and a selected ceramic/aggregate package to produce a self-leveling material that is easily applied with a v-notched trowel or squeegee.

CeRam-Floor TC-1- Topcoat for Floor System is a thin-film, spray or roller applied and air-cured ceramic epoxy system engineered to be cleanable. It is recommended as an economical topcoat over CeRam-Floor Primer or CeRam-Floor - Self Leveling Ceramic Slurry. CeRam-Floor TC-1 is not recommended for areas exposed to UV light.

CeRam-Floor TC-M - Topcoat for Floor System is a thin-film, ceramic epoxy coating system recommended as a topcoat over CeRam-Floor Primer or CeRam-Floor – Self Leveling Ceramic Slurry. CeRam-Floor TC-M offers an amine-blush free cured film and offers excellent water spotting resistance. The cured film is a shiny, slick coating that has excellent flow properties.

CeRam-Floor - Trowelable Resurfacing Material is a high build protective resurfacing system which utilizes 100% solids binder resins and a selected silica sand package to produce a tough and impact resistant resurfacing material that is applied with a hand trowel.

CeRam-Kote Organic Zinc Primer - is a high solids zinc rich epoxy primer for protection of structural steel in salt or weathering environments that will be topcoated with CeRam-Kote products. Not recommended for immersion service. The primer offers excellent adhesion and undercutting resistance. CeRam-Kote Organic Zinc Primer meets most VOC (Volatile Organic Compound) regulations. Available in green only.

CeRam-Kote Thinner 1- is an industrial grade thinner, recommended for use with CeRam-Kote epoxies. CeRam-Kote Thinner 1 is industrial grade MEK and is designed to optimize application/curing results with CeRam-Kote thin-film epoxy products.

CeRam-Kote Thinner 3 - is an industrial grade thinner, recommended for use with CeRam-Kote epoxies. CeRam-Kote Thinner 3 is designed to optimize application/curing results with CeRam-Kote thin-film epoxies iwhen thinning is necessary. Preferred thinner for use in cold climates (60°F / 15.5°C and under).

CeRam-Kote Thinner 4 - is an industrial grade thinner recommended for use with CeRam-Kote epoxies and urethanes. CeRam-Kote Thinner 4 is designed to optimize application/curing results with CeRam-Kote epoxies and urethanes. Preferred thinner for use in warmer climates, (i.e., above 80°F / 26°C).

CeRam-Kote Thinner 5 - is an industrial grade thinner recommended for use with CeRam-Kote epoxies and urethanes. CeRam-Kote Thinner 5 is designed to optimize application/curing results with CeRam-Kote epoxies and urethanes. It is the recommended thinner for hot climates, (i.e., over 90°F / 32.2°C) and to help slow cure time slightly.

CeRam-Thane 100 is a single component thin-film, spray-applied waterborne urethane engineered as a topcoat to provide ultraviolet light resistance and color fastness to almost all epoxy resins. CeRam-Thane 100 can be color matched for most colors. For use in a controlled environment.

CeRam-Thane 200 - is a high gloss, two-component catalyzed aliphatic urethane topcoat. Performs well in harsh atmospheric conditions in agressive industrial environments. Preferred topcoat for CeRam-Kote thin-film coatings, providing chalk resistance, maximum gloss/color retention and flexibility and durability. Available in clear or tinted formulas.

CeRam-Thane 300 - is a heavy duty, high performance, two-component, exterior/interior, VOC compliant, high solids, polyester aliphatic urethane. Super tough, wet-look, high gloss finish with maximum gloss and color retention. Designed to withstand aggressive industrial environments and provide excellent durability against severe weather conditions, prolonged exterior exposure, abrasion, impact and general chemical attack.

CeRam-Kote PCF is a thin-film, spray applied ceramic epoxy coating engineered to provide excellent chemical resistance and corrosion protection to Oil Country Tubular Goods. CeRam-Kote PCF is a highly modified novalac epoxy resin system that has been heavily loaded with a unique package of ceramic particles enhancing its ability to perform well in a variety of aggressive environments. The formula is highly cross-linked to provide chemical resistance.

CeRam-Kote 54® TZS is a thin-film, spray applied ceramic epoxy coating engineered primarily to provide external abrasion resistance and corrosion protection. CeRam-Kote 54® TZS is a highly modified epoxy resin system that has been heavily loaded with a unique package of ceramic particles enhancing its ability to perform well in a variety of abrasive environments.